Borskrúfa með væng

Fylgiskjal 1

Tækniupplýsingar
Ítarupplýsingar

The self-drilling screw with up to 50% time savings when fastening wood to metal substructures, steel, LAFRE^® silver-grey coated.

Cr(6)-free corrosion protection, approx. 500 hrs no base metal corrosion (salt spray test according to DIN EN ISO 9227 – NSS)

Countersunk head with milled pockets for use with hard and soft woods

AW drive system:

Enhanced torque transmission

Longer service life

Optimum centring

Better mounting output thanks to fatigue-free screwing-in; the required contact pressure for transmission of the torques is considerably lower

Largest possible contact surface of bit in screw drive

Even force distribution prevents damage to the surface-protection coating and therefore ensures better resistance to corrosion

Notice

The recommendation for the maximum wood thickness l_H was calculated with reference to the maximum attachment thickness l_U of the substructure.

Wing-pias must be appropriately tested for usability for each application case. Only install using equipment with depth stop and claw coupling.

Drilling screws may only be used where dampness is not to be expected. For fasteners with a construction permit, the permit, and in particular Part 2 "Special regulations", must always be observed.

Material Steel
Surface Flake zinc, silver-grey
Nominal diameter (d1) 6.3 mm
Length (l1) 60 mm
Head diameter (dk) 15 mm
Internal drive AW30
Head type Countersunk head
RoHS-compliant Yes
Thread type UNC
Other standard Company standard
Drill tip length (lp) 6 mm
For min. substructure thickness 2 mm
Max. material thickness to be drilled through (metal) 6 mm
Min./max. recommended installation speed (idling) 800-1200 U/min(rpm)
Max. material thickness for wood (lH) 40 mm

Innskrá til að sjá verð

Vörunafn	Material	Nominal diameter (d1)	Length (l1)	M. í kassa
Borskrúfa 4,8x50 aw20 m.væng 0219 114 850	Steel	4.8 mm	50 mm	500x
Borskrúfa 4,8x50 aw20 m.væng Vörunúmer: 0219 114 850 Tæknilegar upplýsingar Material Steel Surface Yellow galvanised Nominal diameter (d1) 4.8 mm Length (l1) 50 mm Head diameter (dk) 9.5 mm Head height (k1) 4 mm Internal drive AW25 Head type Countersunk milling head RoHS-compliant No Thread type Self-tapping screw thread Sjá allar upplýsingar
Borskrúfa 5,5x38 aw25 m.væng 0219 115 538	Steel	5.5 mm	38 mm	500x
Borskrúfa 5,5x38 aw25 m.væng Vörunúmer: 0219 115 538 Tæknilegar upplýsingar Material Steel Surface Yellow galvanised Nominal diameter (d1) 5.5 mm Length (l1) 38 mm Head diameter (dk) 10.8 mm Head height (k1) 4.4 mm Internal drive AW25 Head type Countersunk milling head RoHS-compliant No Thread type Self-tapping screw thread Sjá allar upplýsingar
Borskrúfa 6,3x60 aw30 0219 664 60	Steel	6.3 mm	60 mm	500x
Borskrúfa 6,3x60 aw30 Vörunúmer: 0219 664 60 Tæknilegar upplýsingar Material Steel Surface Flake zinc, silver-grey Nominal diameter (d1) 6.3 mm Length (l1) 60 mm Head diameter (dk) 15 mm Internal drive AW30 Head type Countersunk head RoHS-compliant Yes Thread type UNC Other standard Company standard Sjá allar upplýsingar
Borskrúfa 6,3x80 aw30 0219 664 80	Steel	6.3 mm	80 mm	250x
Borskrúfa 6,3x80 aw30 Vörunúmer: 0219 664 80 Tæknilegar upplýsingar Material Steel Surface Flake zinc, silver-grey Nominal diameter (d1) 6.3 mm Length (l1) 80 mm Head diameter (dk) 15 mm Internal drive AW30 Head type Countersunk head RoHS-compliant Yes Thread type UNC Other standard Company standard Sjá allar upplýsingar